Physical Address

304 North Cardinal St.
Dorchester Center, MA 02124

Should I spray water on my concrete after it is poured?

To put it simply, the goal is to keep the concrete saturated during the first 28 days. The first 7 days after installation you should spray the slab with water 5-10 times per day, or as often as possible. Once the concrete is poured the curing process begins immediately.

Why is there water on top of my concrete?

Bleed in concrete is the result of excess water being forced to the surface of the concrete. … Any excess water not absorbed by the sand and cement rise to the surface. This leaves a pool of water on the surface of the concrete, which we call bleed water.

What do you do with concrete bleed water?

How long after pouring can concrete get wet?

How Long Does Concrete Take to Dry Before Rain? Even if it starts raining after a concrete pour, the potential for damage may not be that serious. If you had time to complete the finishing process and the concrete has stiffened (typically 4 to 8 hours after mixing), rainwater may cause little if any damage.

How long does 4 inches of concrete take to cure?

Your concrete should be solid enough to walk on, without leaving footprints, after anything from 24 to 48 hours. By seven days, your concrete should be cured to at least 70 percent of its full strength.

Will rain ruin fresh concrete?

Light sprinkles of rain can cause no damage to freshly prepared concrete structures. However, heavy rain showers and thunderstorms cause the surface to become soft and flaky. In such situations, use a plastic sheet for covering the surface or structure.

How do you fix puddling on concrete?

There are basically three choices regarding what to do to repair a concrete slab that has water ponding. You can grind it, replace it, or raise it.

How do you fix standing water on concrete?

Where the water tends to collect, cut out a sloping channel in the concrete to direct the water away, filling it with decorative stone or gravel. Instead of gravel, you can also have a trench or channel drain made of metal installed.

What is concrete puddling?

Puddling is both the material and the process of lining a water body such as a channel or pond with puddle clay (puddle, puddling) a watertight (low hydraulic conductivity) material based on clay and water mixed to be workable.

How long does it take to bleed water to evaporate?

Allow all of the water to disappear before you do anything else. This can take 20 minutes or 4 hours depending on the temperature, humidity and how hard the wind is blowing. After the bleed water is all gone, you can get out your steel finishing trowel and put on the final touches.

Can you smooth out concrete after it dries?

Sand the Surface and Wash the Concrete Finish by fine-tuning with light sandpaper, until the surface is perfectly smooth. We recommend using a hand planer to smooth and compact the surface. If the concrete dries a lot then we recommend that you add water to the surface, this will help you give it a good finish.

When should you Powerfloat?

A rough guide for considering when to begin power floating is when walking on the surface leaves indentations of 3-4 mm. If the concrete is too wet the machine will tear up the surface, and if it is too dry, it will not be possible to trim high spots or fill low spots effectively.

What happens when it rains on wet concrete?

HOW DOES RAIN AFFECT CONCRETE? Rain falling on top of freshly laid concrete can damage the surface and compromise a level and floated finish. Even worse, if too much extra water works its way into the concrete mix, this can result in weak concrete overall.

How often should you water new concrete?

five to 10 times per day DO spray new concrete with water. One of the most common methods for curing concrete is to hose it down frequently with waterfive to 10 times per day, or as often as you canfor the first seven days. Known as moist curing, this allows the moisture in the concrete to evaporate slowly.

How long should concrete cure before removing forms?

Walls and columns can be removed after about 24-48 hours. Slabs, with their props left under them, can typically be removed after 3-4 days. Soffits, with their props left under them, can be removed after one week. Props supporting slabs under 15 feet can be removed after one week.

Will concrete dry if too wet?

When a concrete mixture is too wet, it causes a greater amount of shrinkage during the drying process than is needed. As a result, the concrete has a great likelihood of cracking and for those cracks are likely to be a fairly good size. … A watery mix actively reduces the compressive strength of the dried concrete.

How strong is concrete after 3 days?

Thus, it is clear that concrete gains its strength rapidly in the initial days after casting, i.e. 90% in only 14 days. … Why do we test concrete compressive strength after 28 days?

Age Strength per cent
1 day 16%
3 days 40%
7 days 65%
14 days 90%

How strong is concrete after 24 hours?

Some mix designs reach 5,000 psi of compressive strength in seven days or even in 24 hours. However, the faster concrete reaches the minimum design compressive strength, the greater the cost of the concrete.

Can you walk on concrete after 12 hours?

You should wait at least 24 hours before walking on your freshly poured concrete. However, make sure not to drag your feet, twist around on it, or let your pets with claws walk on it until later. … To minimize scuffing and scratching, wait at least three days before doing any excess activity on top of the concrete.

Is pooling water bad for concrete?

Standing water on a concrete driveway can cause severe damage to the surface. Snow or rain that remains on your driveway may lead to discoloration. Water that gets into any holes or cracks in your driveway can freeze during the winter months and expand to make these holes and cracks larger.

How do you redirect water on concrete?

The best way to divert runoff water away from your driveway is to install a French drain or swale. This drain will intercept the water that runs toward your driveway and channel it downhill. With a well-constructed drain, you can stop your driveway from being flooded with runoff.

How do I remove standing water from my patio?

9 ways to get rid of standing water in yard

  1. Re-grade. Professional landscapers can provide you with a survey of your lawn’s trouble spots, natural drains, and channels. …
  2. De-thatch. …
  3. Aerate your lawn. …
  4. Give your soil a boost. …
  5. Find the hardpan. …
  6. Extend downspouts. …
  7. Raise the soil. …
  8. Install a French drain.

How do you fix standing water at the end of a driveway?

How do I stop standing water in my driveway?

Solution: A driveway drain can be installed at the top of your driveway nearest to the home. This trench drain is long and narrow, and extends from one side of your driveway to the other, helping to ensure that all excess water is caught by the drain, rather than allowed to flow into your home.

How do you fix low spots in concrete?

If you need to level low spots on your floor, use a concrete patching compound. The patching compound also works well to repair any cracks that formed when the concrete settled. You don’t need many tools for this project, but you do need to wear protective gear for your eyes and hands. Work in a well-ventilated area.

What does the word puddling mean?

Definition of puddling : the process of converting pig iron into wrought iron or rarely steel by subjecting it to heat and frequent stirring in a furnace in the presence of oxidizing substances.

What is puddle water?

noun. a small pool of water, as of rainwater on the ground. a small pool of any liquid. clay or the like mixed with water and tempered, used as a waterproof lining for the walls of canals, ditches, etc.